Dilute one filling station control system Harvester dilute the original oil pump station is by detecting the pressure to control their working condition. Petrol filling stations equipped with three pressure gauges, oil pressure, respectively, after filtration pressure, oil pressure. Oil pressure...
8, start-up failure (1) can not start. Light bulb with a multimeter or test to check the availability of start-up between the motor terminal voltage 12V. If so, then there is no starter motor failure, if not, then start switching undesirable insects survey should be repaired or replaced. (2) unable...
7. Chain fracture Chain tightness inappropriate; chain eccentric wear; shaft bending, so that deflection sprocket; chain continue to be used after a serious wear and tear; sprocket wear more than allowed limits; sleeve roller chain wear forelock falling off, or the direction of joint Nagarze...
6. Screen surface plug Mainly due to improper adjustments threshing device, broken stem too much, fans do not justify blowing up objects, so that the front was broken sieve stem, Sui "blocked" and caused by pushing transportation device overload or blockage; cleaning devices improper adjustment ,...
combine parts
Rollers from non-net Roller speed was mainly due to too low, intaglio gap is too large, excessive or feed crops feeding uneven; nail tooth, stria rods and intaglio rack excessive wear, threshing ability to reduce, or intaglio deformation caused by non-threshing net; premature harvest...
combine parts
Drum plug Crop is too wet, too dense, weeds and more; to walk too fast; threshing gap small, or low-speed roller; transmission belt skid; engine power is insufficient; draft by draft-by-round and do not switch skid device; feeding inequality can caused drum plug. In order to prevent...
combine parts
Cession of Taiwan spiral push shipped skid device Yun push of spiral blade and cut the gap between the floor and Taiwan is too large, especially in the rare dwarf wheat harvest, the leaves have been cut grip crops, timely delivery, in the push before the accumulation of...
Straw Chopper break Mainly due to the knife cut too much resistance movement or a knife cutting drive mechanism of the incorrect location of the installation. To prevent break Straw Chopper , the right to adjust the cutter so that the cutting knife to reduce the resistance movement, a knife cutting...
1. Damage to the Knife Section In the process of cutting stone-faced, hard object, such as roots; care or loose blade deformation device, so that the blade set the level of inconsistency; blade loose rivets, cutting and so on, may encounter when the Knife Section damage. To prevent damage to the...
4. Technology custody. By combine the custody of the idle time to ensure that its integrity and good. â‘ remove dust and dirt, open the window all the crew, cover, guard and seriously to clear built-in throughout the Clipping, broken stalks, oil pollution, so that the cleaning crew. â‘¡...
3. The proper use and operation. According to the norms of failure to reduce operating efficiency. â‘ not start the engine load, combine parts with low-speed clutch, pulled control valve so that combine to slow down, Taiwan will be reduced to a normal harvest cut stubble height increased...
2. Technical maintenance. On a regular basis on various parts of the combine cleaning, inspection, fastening, adjustment, lubrication, and add the replacement of parts and components, and other vulnerable operations. â‘ combines the clean, clear machine-hull, broken stem and other attachments,...
1. Test run. The new machine or maintenance after the harvester, the need for commissioning run-in. â‘ engine test run. According to the maintenance overhaul, decided to cold, hot run-in operation, check oil pressure gauge, thermometer oil, water tables are in working order, whether or not...
5, It should be regular and timely inspection of the combine, maintenance and repair. If the check Queyou, lack of water, whether there is a loose, open whether welding, whether or not sound so unusual. If abnormal, should be promptly added that the restructuring and repair, the machine should not...
3 Harvest crops because of different conditions (such as crop varieties, maturity, moisture content, production, crops and a high degree of lodging, such as the situation varies), so combine the use of the process, should focus on the crop conditions , To adjust the machine in a timely manner all...
Any machine, the length of their service life, high and low failure rate, is safe and reliable, and so on, in addition to the machine itself, manufacturing quality, with the use of machinery and maintenance also have a great relationship. The use of combine harvesters is no exception, it should be...
Combine Harvester Parts
new products - rasp bar.
we also supply Pressed Knife Guard Forged Knife Guard Casting Knife Guard Harvester Blades Straw Chopper Knife...
Combines a set of harvesting, transportation, threshing, separation and cleaning functions of a joint operating crop harvesting machinery. Combine the purchase should be based on the area of operations, the harvest target, the nature of operations, manufacturers and network services to three bags...
Combine Parts in China
In 1799 first appeared in Britain's Mara disc cutter harvester; in 1822 in the knife cut the top of the increase in the allocation of the Wo device. Reciprocating appeared in 1826 using cutters and set aside Wo round of the harvester prototype of the modern, multi-use...
In 1889, the Americans Best designed and manufactured the first by a steam engine-driven self-propelled combine, one day up to harvest more than 50 hectares of farmland. Since then, they have been born by the internal combustion engine-driven self-propelled combine. In the 1920s, combine first in...
Bookmark this page